{"product_id":"lz-spec-e36-angle-kit","title":"FDF Raceshop - LZ Spec E36 Angle Kit","description":"\u003cp\u003eThe LZ Spec E36 Angle Kit was built for one driver. Adam LZ told us how he wants the front of his E36 to feel, and we built the geometry around the way he drives. High KPI for steering feel, a lot of positive Ackermann and a strong centering force, all locked in where Adam runs his winning setup.\u003c\/p\u003e\n\u003cp\u003eThere's very little to tune. Camber and caster adjust at the top hat and bump steer is set with washers at the outer tie-rod. Everything else is fixed, so you bolt it on and you're running the same front end Adam does.\u003c\/p\u003e\n\u003cp style=\"margin: 18px 0;\"\u003e\u003ca href=\"\/en-ca\/pages\/lz-spec\" style=\"display: inline-block; background: #017f59; color: #ffffff; font-weight: bold; text-decoration: none; padding: 12px 20px; border-radius: 6px;\"\u003eSee the LZ Spec geometry\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003eTurn the wheel and see the Ackermann, weight jacking, KPI, caster and roll center on the real kit geometry.\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003eKey Features:\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAngle:\u003c\/strong\u003e 70 degrees at full lock.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eKPI:\u003c\/strong\u003e About 23 degrees. Turning the wheel lifts the front of the car, so the wheel comes back to center quickly and you can feel exactly where the front tires are.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight Jacking:\u003c\/strong\u003e At 40 degrees of steering the inside front corner lifts about 22mm. That puts load on the light rear tire in a drift and gives more forward bite at big angle.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAckermann:\u003c\/strong\u003e Positive Ackermann, about 2 degrees more on the inside wheel at 40 degrees and more near full lock. The front tires drag against each other a little, which makes the front end lighter and lets it slide.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCaster:\u003c\/strong\u003e About 8.7 degrees with 35mm of trail, for a strong, steady centering force that isn't heavy at full lock.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eScrub Radius:\u003c\/strong\u003e About 28mm. Enough to feel the tire, small enough that bumps and brake loads don't pull the wheel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCamber and Caster Adjustment:\u003c\/strong\u003e Adjusts at the top hat, about 20mm each way. Adam runs the middle of the slot.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBump Steer:\u003c\/strong\u003e Adjustable with washers under the outer tie-rod end.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoll Center:\u003c\/strong\u003e About 150mm off the ground at Adam's ride height, so the front still rolls and loads the outside tire through a transition.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003cstrong\u003eAdam's Setup:\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFront Tire Pressure:\u003c\/strong\u003e 16 to 24 psi to balance the front against the rear. He airs the fronts up over 50 psi for backwards entries.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFront Toe:\u003c\/strong\u003e 1\" out on flat tracks, 1\/2\" out on banked tracks.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFront Springs:\u003c\/strong\u003e 12 kg\/mm (about 670 lb\/in) with a large aftermarket front sway bar and no rear bar.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFront Wheel:\u003c\/strong\u003e BC Forged 17x9 +12.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eUse these as a starting point. Adam's full setup, including his ride heights, is on the LZ Spec page.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNote: \u003c\/strong\u003eYou must have coilovers to run this kit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e*Fits the non-M3 E36 only. Not compatible with the E36 M3*\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cstrong\u003eIncludes:\u003c\/strong\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e2 knuckles\u003c\/li\u003e\n\u003cli\u003e2 lower control arms\u003c\/li\u003e\n\u003cli\u003e2 inner and outer tie-rods\u003c\/li\u003e\n\u003cli\u003e2 top hats (camber and caster plates)\u003c\/li\u003e\n\u003cli\u003eAll bearings and hardware required for install\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote: \u003c\/strong\u003eThe kit is powder coated in Highland Bronze, Adam's color.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e Orders require 2-3 weeks for fabrication before shipping.\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0049\/8044\/1155\/files\/E36-12-500_INSTALLATION_MANUAL.pdf?v=1793896119\" target=\"_blank\" rel=\"noopener\"\u003e\u003cspan style=\"text-decoration: underline;\"\u003e\u003cstrong\u003eInstallation Manual\u003c\/strong\u003e\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003ch3\u003eWhy Choose FDF?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDriver-inspired designs:\u003c\/strong\u003e Our products feature innovative, driver-inspired designs tailored for performance and style.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-quality materials:\u003c\/strong\u003e We use only high-strength alloys to ensure the durability and superior quality of our products.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMade in North America:\u003c\/strong\u003e Our products are proudly made in-house in North America, ensuring exceptional craftsmanship and reliability.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"FDF Raceshop","offers":[{"title":"Default Title","offer_id":68117083160763,"sku":"E36-12-500","price":2811.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0629\/9556\/2683\/files\/AdamLZE36AngleKit.jpg?v=1793979780","url":"https:\/\/drifthq.com\/en-ca\/products\/lz-spec-e36-angle-kit","provider":"Drift HQ","version":"1.0","type":"link"}