{"product_id":"wisefab-toyota-supra-a90-front-drift-angle-lock-kit-wfa90","title":"WiseFab - Toyota Supra A90 Front Drift Angle Lock Kit (WFA90)","description":"\u003cp\u003eThe Toyota Supra A90 is one of the most discussed new cars around. Rear wheel drive together with turbocharged in-line six engine offers great potential for drifting. Here at Wisefab we have developed PRO level lock kit for this chassis. It has been tested in Japan and USA by the best drivers around and we are happy to offer this product now to our customers.\u003c\/p\u003e\n\u003cp\u003eAll the metal components on Wisefab A90 front suspension are from high strength steel, including sheet metal components, tubes, tube ends and rod end housings. Rod ends and spherical bearings are used, no rubber bushings.\u003c\/p\u003e\n\u003cp\u003eWant to know how does Wisefab Lock kit fits your driftcar check below the link \u003cstrong\u003eCHECK FITMENT \u003c\/strong\u003eor \u003ca href=\"https:\/\/www.wisefab.com\/fitment-calculator\" target=\"_blank\"\u003ehere!\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003eHere is our recommended alignment parameters:\u003cbr\u003e\u003cstrong\u003eToe in\/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive then toe is 0\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eCamber: -7 +\/-0,3\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eCaster: 6 +\/-0,3\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cdiv class=\"product attribute description\"\u003e\n\u003cdiv class=\"value\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cspan\u003e65 degrees of lock, parallel steering.\u003c\/span\u003e\u003cbr\u003eYou could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment.\u003cbr\u003eAckermann adjustment kit included.\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eAdjustable lock stopper.\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eOne piece lower control arm desing.\u003c\/span\u003e\u003cbr\u003eLower links are replaced with one arm. Drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eHigher roll center (RC).\u003c\/span\u003e\u003cbr\u003eOn Wisefab knuckle, joints are dropped, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles. \u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eVery good camber control and minimal bump steer with high steering angles.\u003c\/span\u003e\u003cbr\u003eOn drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eSteering jacking control.\u003cbr\u003e\u003c\/span\u003eDuring drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eConsistent and predictable self-alignment torque.\u003c\/span\u003e\u003cbr\u003eCaster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. \u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eOriginal wheelspeed sensor (ABS sensor) can be used.\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eKit includes\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable coilover upper mounts, Formula Drift compliance.\u003c\/li\u003e\n\u003cli\u003eKnuckles with hardware.\u003c\/li\u003e\n\u003cli\u003eLower control arms.\u003c\/li\u003e\n\u003cli\u003eAssembeled tie rods.\u003c\/li\u003e\n\u003cli\u003eBrake adapters for M model brakes.\u003c\/li\u003e\n\u003cli\u003e45mm coilover adapter sleeve.\u003c\/li\u003e\n\u003cli\u003eInstallation guide.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eImportant details about component fitment\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWheel bearing: Front wheel bearing has to be sourced from BMW E90. Part number 31216765157. OEM can not be used.\u003c\/li\u003e\n\u003cli\u003eWheels: Wheel bearing has 5x120 PCD. This means that OEM wheels can not be used.\u003c\/li\u003e\n\u003cli\u003eBrakes: We recommend using brakes from BMW E90 or E90 M3. OEM brakes caliper can be used with the supplied E90 M3 brake caliper adapter. Brake adapter may need some modification. OEM brake disc can not be used. When using OEM brake caliper suitable brake disc needs to be sourced. Make sure that the brake disc is centered in the caliper\u003c\/li\u003e\n\u003cli\u003eStrut: Strut lower fixing diameter has to be 56 mm or 62 mm. OEM fixing diameter is 56 mm. Ride height adjustable coilovers must be used.\u003c\/li\u003e\n\u003cli\u003eSteering rack: We do not recommend using the OEM steering rack but it can be used. If the steering rack is changed it has to be mounted exactly where the OEM steering rack was.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"WiseFab","offers":[{"title":"Default Title","offer_id":43931994554555,"sku":"WiseFab-WFA90","price":2990.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0629\/9556\/2683\/products\/image_220570ef-b365-426c-83b0-692429578645.jpg?v=1668965648","url":"https:\/\/drifthq.com\/products\/wisefab-toyota-supra-a90-front-drift-angle-lock-kit-wfa90","provider":"Drift HQ","version":"1.0","type":"link"}